Today I’m going to show you how to make Origami Kusudama Flowers. It’s hard not to love such a versatile material. Along with these flowers I’ve made gift boxes, wall art, bows, bookmarks, decorations and more. I know it might be hard to believe but this pretty paper flower is actually super simple to make and is the perfect starter project for a beginner.Īnyone who is a regular reader knows how much I love making papercraft, particularly origami (I even have a whole ebook about it). It’s always so fun to see what can be made simply by folding a square of paper. One type of DIY that I can never get enough of is origami. This means that if you make a purchase after clicking a link I earn a small commission but it doesn’t cost you a penny extra! Easy Origami Flowers. In case you have any doubt regarding any step, here is video tutorial to make the flower.This page contains affiliate links. Now apply glue to the sepal and insert that as well and stick it to the base of the biggest layer. Do the same procedure as with the rose layer. Now, take the bigger petal layer (red) and apply glue to the centre of it.Ħc. Press the base of the petal layer onto the base of the stigma piece and at the top of the stem. Insert the stem into it along with the stigma. Take the smaller petal layer (rose color)and apply glue to the center. Keep the stem inside and roll it while making sure the stem is stuck to the stigma.Ħb. Take the pistil stigma paper piece and apply glue to its base. Trim the edge to make the end of the stem look even (5e). Now roll the paper diagonally as thin as possible (5b and 5c). To make the stem, take a green paper and cut a rectangle of size 10cm x 12 cm (5a). Step 5: Make the stem of the paper flower When you look at the picture 4g, the base is the part that comes under the finger. Now make a small cut at the bottom to make a hole to insert the stem later(4h). It’s not exactly middle, but a little bit towards the left vertex of the triangle (see the arrow in 4f).Ĭut along the arc (4g).
Keep the triangle in the exact position as shown in pic 4f.ĭraw an arc starting from near the middle of the horizontal edge of the triangle. Now fold the square piece diagonally (from left top corner to right bottom corner) to get a rectangle as shown in pic 4e. Fold it again in half from left to right and make a crease (4c and 4d). Now, take a green color paper and cut a square of size 6cm (4a).įold it in half from the bottom to top (4b) and make a crease. It is important so as not to go wrong with the cutting. In this step, you have to hold the square paper without changing the position.
Keep it aside and let’s move on to making the sepal of the paper flower. Open the paper and there you have the pistil stigma of the paper flower (3h). And take a scissors to cut thin vertical lines as shown in pics 3f and 3g, leaving some width at the opposite edge to roll the paper so that we can make the stigma. Keep folding it again and again at the same width until you reach a size shown in pic 3c and 3d.įold the remaining part (3e). The width doesn’t matter here as this is just to make it easy to cut the paper thinly to make pistil stamen. Now fold it at a width of approximately 2-3 cm (3b). Step 3: Make the center of the flowerĬut another color paper in rectangle shape of size 10cm x 4cm (3a). To make the next petal layer, cut a square of size 10cm.
You can understand the steps from the pictures below. So, I am not going to write about the details. We will repeat the same procedure as in step 1. For this, take another color paper of your choice. In this step, we are going to make the second smaller petal layer. Open the figure to get one of the petal shapes (1j). The next step is to make a tiny hole at the opposite corner of the petal shape (1i). You get the petal shape as shown in pic 1h. Now, draw the shape of two petals as shown in pic 1e. Now fold again in half from left to right and make a crease (1d). Glue Step-by-step tutorial for a simple flower craft Step 1: Cut a square paper to make the flower petalsįold it in half from bottom to top so that the bottom two vertices meet the top two vertices (1b).If it resembles any flower you know, let me know in the comments below. So, let’s just call it a “Random Beauty”. In this post, we have come up with a tutorial to make a beautiful and easy paper flower. You can make paper flowers as home decor or as a fun useful craft to pass time with kids. And you don’t always need fresh flowers to add beauty to your space.
0 kommentar(er)
